Grid View:

GRUB SCREWS 3MM X6MM FOR CKP ROUTER BITS

(0)
R18.80

Spare Screw for Router Bits Thisis an affordable router bit range that is well supported throughout South Africa. Allour Tork Craft router bits are Tungsten tipped. Tork Craft is a well-known BRANDin most retail stores.At a glance:Spare screw for holding the bearing in place onour Tork Craft router bit range...

GRUB SCREWS 3MM

(0)
R6.73

Grub screw (short) 2.4mm Grub screwThe grub screw is used to hold the bearing to the router bit.Make sure that the washer is fitted between the grub screw and the bearing...

KP GRUB SCREW 2.4MM

(0)
R6.73

Grub screw (long) 2.4mm Grub screwThe grub screw is used to hold the bearing to the router bit.Make sure that the washer is fitted between the grub screw and the bearing...

RETAINING COLLAR/TOP BEARING 1/4'

(0)
R25.53

Retaining collar for 1/4' shaft router bits Retaining collarThe retaining collar is used to secure a bearing with an internal diameter Ø 1/4' to a 1/4' shaft router bit.Secure the retaining collar by tightening the supplied grub screw...

RETAINING COLLAR 1/2'

(0)
R25.53

Retaining collar for 1/2' shaft router bits Retaining collarThe retaining collar is used to secure a bearing with an internal diameter Ø 1/2' to a 1/2' shaft router bit.Secure the retaining collar by tightening the supplied grub screw...

ROUTER BIT SPARE PART PACK

(0)
R186.42

Router bit spare parts pack Spare partsincludedAllen keyBearing ID 3/16' x OD 1/2' -KP100 1-2Bearing ID 3/16' x OD 3/8' -KP100 3-8Grub screw -KP GRUBDust seal for 1/2' bearingDust seal for 3/8' bearing..

BULL NOSE RADIUS 1/2' X 20MM FULL RADIUS 12.7MM 1/2' SHANK

(0)
R506.92

Half RoundBull Nose Bit CarbideTippedThisrouter bit is used for creating a convex shaped profile on the side of the workpiecein one pass producing a perfect half radius bull nose profileDesign helps minimize kickback Smooth edge requires little or no sanding before applying finish This router bit has a12,7 mm shank (shaft) that will fit most large ..

BULL NOSE RADIUS 3/4' X 29MM FULL RADIUS 1/2' SHANK

(0)
R966.81

Half RoundBull Nose Bit CarbideTippedThisrouter bit is used for creating a convex shaped profile on the side of the workpiecein one pass producing a perfect half radius bull nose profileDesign helps minimize kickback Smooth edge requires little or no sanding before applying finish This router bit has a12,7 mm shank (shaft) that will fit most large ..

REPLACEMENT 3.2MM CUTTER FOR THE V JOINT TONGUE & GROOVE ASSE

(0)
R372.83

REPLACEMENT 3.2MM CUTTER FOR THE V JOINT TONGUE & GROOVE ASSE..

SLOT CUTTER 4MM FOR KP551 OR KP851

(0)
R207.86

SLOT CUTTER 4MM FOR KP551 OR KP851..

OGEE CUTTER 12.7MM FOR KP551 OR KP851

(0)
R398.25

Spare cutter Routerbit spare partThis ogee cutter cuts 12.7mm instead of the 9.5mm standard and is compatiblewithKP551 andKP851...

SPARE OGEE CUTTER STANDARD SIZE FOR KP551 0R KP851

(0)
R368.75

Spare cutter Routerbit spare partThis ogee cutter cuts 9.5mm and is the standard cutter supplied withKP551 andKP851...

SLOT CUTTER 6.35MM

(0)
R258.87

Slot cutter Routerbit spare partThe slot cutter cuts 6.35mm in width and is compatible withKP551 andKP851...

SPARE CUTTER FOR609011/551/851

(0)
R187.22

Sparecutter (slot cutter) Router bit spare partThe slot cutter is compatible with the following cutters:KP609011KP609411KP851KP551..

SHAFT AND BEARING FOR KP609011

(0)
R146.22

Sparearbor Router bit spare partThe arbor is compatible with the following cutter:KP609011..

SPARE CUTTER FOR KP7004 4MM

(0)
R308.03

BiscuitSlot CutterReplacement blade ForBiscuit slot cutter KP7004 & KP7005The biscuit slot cutter comes in handy when one does not have access to abiscuit joiner.Our Pro-Tech four-wing cutter design allows for cutting precise slots for No. 0, No.10 and No. 20 biscuits. The bearing guide needs to be replaced with a different size in orderto accommod..

Out Of Stock

SHIM 1/2'

(0)
R31.97

SHIM 1/2'..

EMPTY WOODEN BOX 24PCE

(0)
R625.20

Routerbit storage Router bit storage boxThe box is made to store 24 1/2' shank  router bits...

SPARE BLADE FOR FINGER JOINTER

(0)
R885.04

Spareblade Router bit spare partThe cutter blade can be used as a spare blade for the KPFJ-01 fingerjointer or it can be added to the stack of finger jointer blades to have atotal of 4 blades...

Showing 1 to 19 of 19 (1 Pages)